Swirl Bowl - a $0 Cost Tangential Twist Turning

by bippy8 in Workshop > Woodworking

5840 Views, 43 Favorites, 0 Comments

Swirl Bowl - a $0 Cost Tangential Twist Turning

a 010 fin1.png
scrap treasures1.png
a 011 wedge scraps.jpg
a04.jpg

I love to find reuses of scraps (some people call it trash). I find it fun to give rebirth to these hidden gems and turn them into something interesting. I've tried this with bowls and pens made from plywood scraps (also even used old skateboard decks), made kazoos from flooring scraps and cabinets doors, rings from veneer scraps and car paint and also a table from a old 2x4. So I loved seeing this ible challenge since it is right up my trash picking alley.

A little background first, my wood club makes toys for less fortunate children (we typically make 4,000 - 5,000/yr - I'm task to make 150-200 kazoos :-). One of my club members makes a toy called a "flip car" that goes down a short ramp and flips over itself and keeps going. Part of the ramp has a wedge cut off to provide flat section to start the car off. Needless to say that when making hundreds of these toys, there are a plethora of short wedge scraps generated as "waste" but not to me! My club member challenged me in front of the entire club to make something from them. So I did.

BTW, I learned a lot in the process and tried several new techniques. Surprisingly it turned out very nice and won the top award at my club and also an award our our county fair. I hope you enjoy.

Supplies

a 02 wegde.jpg
a 011 wedge scraps.jpg

Used typical woodworking tools. Many I obtain from craigslist very cheap. Tip if you join a local wood club many members are eager to help you out and mentor so take advantage of these great artisans.

Wedge Wood Scraps (mine were 2.5" H x 3.25" L x 0.5" W at the thick end and went down to 1/16" at the tip (they were at an ~11-12 degree angle)

Wood Veneers (free from my club member)

Table Saw

Lathe

Sanders

Press to make veneer sandwich and compress the wedges into a tight tangential twisted

Clamps

Tennis Ball or Cone

Tons of glue (Tight Bond II)

Design With Interesting Geometry

a 01a radial tangential segments.jpg

This was the interesting part. I was watching my nightly YouTube woodworking videos and came across an interesting one that used a tangential twist technique. The original concept came from Robert (Jerzy Gryglaszewski) Craig (article here). I used a variant approach which involved creating wedges and orienting them tangentially around a center (see pic). Then you move them around until to eventually get then to seat perfectly flat against each other (TIP: you might have to remove some to get alignment). Well this amazed me since one of the big challenges in making segmented bowls is to cut each piece at a precise angle. If you are a little off then there will be very noticeable gaps that have to finessed to make flat (i.e., sanded). For example, just 0.1 degrees/piece off and with 12 pieces, this can yield a 1.2 degree gap. Now imagine have ~30 segments - that's 3.6 degrees to fix which is a tedious process.

The Tangential Twist approach purportedly assured perfect alignment. So you can imagine I was excited to have a box of little wedges for me to try this out.

One challenge I quickly learned. These wedges were inconsistent in the angle and ranged from 11 - 12+ degrees; so I didn't know if the process "woodwork" (pun intended).

Spoiler alert - it did.

Prepare Veneers

a 03 prepare veneers.jpg

To create an interesting pattern for the twist, I decided to make a sandwich of veneers as separators between the wedges to make them more visible and create a nice spiral pattern. My veneer sandwich was made out of Maple +2 Walnuts + Maple and I pressed them tightly in my vise then cut them the size of the wedge side.

Prepare Wedges

a 04 prepare wedges.jpg

Next, I glued the veneer sandwiches to the wedges and lathered both sides with tons of glue to prepare for tangential assembly. TIP: Before I glued up the wedges and did a dry assemble to see if all this would work out and this test gave me some confidence it would.

Glue Up - Work Fast

a 05 glueup.jpg

Once the glue is on the wedges, you have around 15-20 mins to get all the wedges set up around a ball (or cone) to create the tangential assembly. I wrapped the assembly with plastic then tightened with band clamps top and bottom. Finally, I put the assembly into a press and tightened as much as possible while checking the band clamps and tightening them too if needed.

Now you hope and pray it will all work. BTW, I had no way to see if the wedges aligned flat with each other or now.

I kept in the press for a week before I unwrapped. Since there was plastic the glue wasn't fully dried so I removed the plastic and let it set another week. I as pleasantly surprised with the result - Perfect alignment from wedges that were at different angles.

Flatten the Assembly

a 06 flatten.jpg

I needed to create a flat bottom so I could mount the assembly on my lathe. So I used a belt sander to flatten the bottom and then ran it thru my drum sander for the top. I loved the pattern it made. Sort of hypnotic.

Lathe to Shape

a 07 lathe.jpg

You may think this is funny but the hard part is over. To get to this step took 3 weekends and the lathing just a few hours. To me it looked like a cantaloupe so I decided to shape it a bit like that. I mounted a piece of exotic rosewood that another cub member gave me as the base.

Tweaking

a 08 tweak.jpg

At this point I was almost satisfied with the shape but still felt it needed a little more to make it even more special. I brought it to my club meeting to get their opinion (many are very accomplished world class turns). I was debating if I should angle the top of the bowl down or up a bit. So a suggestion was made to use a paper model to help visualize the shape. That was very helpful and I decided to tip the top up.

Finish

a 09 finish.jpg

The best part of wood turning is to put on the finish to make the piece come alive. I used a home made friction polish (approximately equal parts: Denature Alcohol, Boiled Linseed Oil, and Wax Free Shellac (there are many YT videos on the process). I completed by buffing to a high luster.

Present

first place2.png
a 011 fin2.jpg
a 012 fin3.jpg

Viola! It's a winner.

I especially like how the outside and inner twist around and it's even fun to hold since it has a nice weight. I added a small glass candle holder and my wife always laughs when I show it off when guest come to visit. Now I can just send them to this ible (but I'll still show it off)