Steampunk Lugsail Land Windsurfer

Here's a lugsail land windsurfer that will go with your top hat or pith helmet.
To my surprise it works really well.
It's a work in progress, I'm gradually replacing modern parts with "authentic" ones.
Here's some video of previous landsailers in action.

If you haven't yet met Steam Punks, they're people who dress up in classic outfits and build machinery with a Victorian era aesthetic.
Here's my contribution to the movement, a land windsurfer with a 3.6 meter lugsail.

It sails just exactly like a regular windsurfer. Sail tuning is a little different, due to having four corners to adjust rather than the old three. Study up on lugsail tuning.

The board is any skateboard you're willing to drill a hole in the front of.
Later you'll make a truly Victorian skateboard.

The gooseneck can be almost anything, a universal joint from an old car's steering column, two interlocking eyebolts, or a simple loop of cord.
For the first tests I innertubed a regular mast base to the mast and bolted the universal to the board.

Here's the lugsail.
I made it for a tandem kayak in 2004 by cutting the head and foot off a nice old windsurfer sail.
The design came from "sailmaker's apprentice" adapted to the shape of the original windsurf sail.
I cut and hemmed it and added reef points and grommets.

The spars are all cut down from scrap sticks of 2x4 lumber.
The boom jaws are made from the basket of a lacrosse stick.

We're not going to use this boom for the windsurfer, we'll use a wishbone boom instead.

I originally made this 3.46 sq. meter lugsail for my Klepper Aerius 2 tandem folding kayak.
It was about the right size except when a howling gale was blowing.
I made it from a well-preserved windsurfer sail, which had some broadseaming.
Broadseaming means making the seams between panels a varying width so as to make the sail like a shallow bowl. For more belly, add a bit of edge rounding to the bottom of the head of the sail.
For less belly, cut it straight.

The outhaul is left just the same as it was on the windsurfer.
The peak is reinforced with a couple of patches and grommeted.
The grommets were all brass plated crap, not brass. That was a mistake. They rusted and will soon break.
There are a row of grommets along the head of the sail to spiral lace it to the yard.
The throat is basically the same as the peak.
The tack of the sail has a quarter riveted next to it as a cleat for the luff line.

I drilled a hole in the masthead for the halyard to run through.
The halyard is tied to the yard with a slipknot. The location where the halyard is tied to the yard is important, move it around til the sail shape develops as you like.

The sail worked well with the commercial aluminum wishbone boom, so I decided to make an "authentic" wooden one.

I laminated the front curved parts of the boom from some fir studwood.
The straight tail part is redwood, attached to the front with a stepped scarf and a lashing.
The boom has a keyed block lashed on at the front and simpler block lashed on at the tail to complete the teardrop-hoop shape.

I dug through my woodpile til I found enough fir 2x4 and 2x2 sticks that were good enough.
Then I ripped them into 1/8" thick strips on the tablesaw using the thinnest blade I had.
Some of the source lumber had knots partway through or other problems. I only got a few laminations out of some sticks.

more steps:
Mix up some epoxy and thicken it with an equal quantity of white flour.
Lay out the laminations and paint the glue on one side of each one with a paintbrush.
Stack up the laminations and lash them against a piece of a windsurfer boom I liked.
Use bicycle innertubes to press the laminations together and hold them to the right shape against the form.
Shift the laminations to approximate the taper I want at both ends. That makes the wood overhang the end of the tube. Shove a pick head into the end to lash the innertube around.
Set the layups in the sun to cure. When it's tacky put it in a car in the sun with the windows closed to get hot and fully cure.
When the glue was good and hard take the bandages off and shave the boom smooth.

I used a scarf joint to add a few feet of redwood to the tail of the boom.
That saved me the trouble of laminating the full length of the boom and the trouble of finding long wood good enough to do it with.
I used a Japanese pull saw and a knife to cut the scarves.
Next time I'll cut a the easier straight scarf and add a key to keep the halves from slipping.
As seen in this illustration from "The Elements of Boat Strength" P.138

Then I wrapped it with a lashing of innertube. It feels good ans solid.

For the front I cut this keyed block from two layers of 1/2" plywood and lashed the whole joint with innertubes.
After some testing I'll probably drill holes and redo the lashing with polyester string and soak it with epoxy to make it permanent.

R+D on the venerable lugsail goes on around the world, as on the
woodenboat forum