Reuse Video Game Controller for People With Quadriplegia Like Christopher Reeve

by olmanorozco in Circuits > Assistive Tech

165 Views, 1 Favorites, 0 Comments

Reuse Video Game Controller for People With Quadriplegia Like Christopher Reeve

sy.jpg
IRAZU Joystick with a sip/puff switch Short

Hello everyone! Today I want to talk to you about an assistive technology project called Irazu. This project aims to provide a low-cost and accessible solution for people with physical disabilities.

Irazu is a joystick with a sip/puff switch designed for people with motor limitations, especially those with quadriplegia or degenerative conditions with head movement preservation.

Its easy use and adaptability make it accessible for a wide range of users with different needs and abilities.

In addition, it is an open-source and environmentally friendly project, as it uses recycled materials and reduces the need to dispose of electronic devices.

In summary, Irazu is an innovation that helps improve the quality of life for people with physical disabilities and reduces the environmental impact of technology. A great project that deserves to be known and spread!

Supplies

F6DSPD3LCVYLCBG.jpg

Soldering Iron.

Tin.

Screwdriver.

Hot glue gun.

Cutter / Scissors.

Flat cable.

Game pad.

Balloon #7.

Pencil.

Plastic bottle caps.

Microswitch.

Mini Drill Bits

Drill.

Clips.

Teflon Tape

52.jpg
54.jpg
60.jpg

We will check in the "mouse emulator" of the computer:The configuration and control of the mouse movements, with the joystick of the gamepad.

the assignment of the mouse click to the L2 trigger of the gamepad, which is the one that we will connect with our switch.

Now...

We locate all the screw holes. and we remove all the screws,

Gently, we remove the side pieces of the plastic container of the Gamepad.

66.jpg
68.jpg
72.jpg
80.jpg
62.jpg
64.jpg

We locate the electronic board that has the button that presses the L2 trigger

The following steps will be carried out on welding points 1 and 2.

With the cautin, we solder each flat cable to each union points.

Attention:

The welding points must be separated.

Without touching it each other in any way

84.jpg
88.jpg
90.jpg
96.jpg
98.jpg
100.jpg
102.jpg
105.jpg

Gently remove the screws from the joystick plate.

We will pull up gently, to separate the thumbstick from the joystick control.

With the "Mini Drill Bits", from the smallest to the bigger, we begin to make a hole in each compartment that we select.

We pass each cable through the holes, from the base to the top of the Thumbstick.


We place it back the thumbstick

and we reassemble the control by putting all the pieces back into place.

we left out 2 casing screws that are not so necessary

119.jpg
121.jpg
123.jpg
125.jpg
127.jpg
129.jpg
131.jpg
133.jpg
135.jpg

With a sandpaper we smooth the inside of the soda caps, so that one enters the other.


We make a hole in one of the lids the size of the tip of the pencil


We place the tip of the pen in the hole and hold it with a side clip and silicone

147.jpg
151.jpg
153.jpg
159.jpg

we make 2 holes for the cables, and we place the soda cap on the thumbstick

securing it with the two screws.

Be careful not to break the wires.

157.jpg
163.jpg
165.jpg
167.jpg

We solder the wires to the switch and place it with silicone inside the soda screw cap

171.jpg
173.jpg
175.jpg
177.jpg
179.jpg

We cut the edge of the balloon to have a circle that we will place between the soda caps,

we seal the side air vents with teflon tape

to form a diaphragm that activates the switch with the blow.

179.jpg
180.jpg

when placing the rest of the pen when you blow you will hear the click of the switch


now you just need to connect it to your computer and use any emulation program compatible with the control you adapted