Pantry Storage Built Into Wall Studs

by MeaganJG in Workshop > Home Improvement

404 Views, 3 Favorites, 0 Comments

Pantry Storage Built Into Wall Studs

20241111_193336.jpg
20241112_095647.jpg
20241111_193336.jpg
20241111_193316.jpg
IMG_20241111_192037.jpg
20241111_195313.jpg

We bought a tri-level home that was built in 1974 and I have been desperate for pantry storage. I had this idea that I could take a blank wall, that I hated, and turn it into something cute and functional. I had this idea in my head that I could hide the storage by making it look like art somehow. I wasn't sure how I was going to achieve that when I started. In fact most of the way through this I thought I would have to paint the cabinet doors. I could not find any ideas online at all. This was a real "trust the process" project ... even though I was making up the process as I went. I had to trust my own creativity and skills.

Supplies

Drywall saw, miter saw, 2x4 boards, 1x4 boards, 1x2 trim board, paint, shelf liner, mod podge, canvas print, cabinet doors, hinges, drill, screws, mallet, brad nailer, and brad nails. I will explain the uses in the steps, lots of these supplies can be changed to what you have on hand.

Cut the Hole in the Wall

IMG_20241112_100713.jpg
20240314_125315.jpg
20240314_125318.jpg

The unavoidable first step, cut the hole. At this point I did not have a clear idea of how this would look finished, but I knew we needed the storage. I had an idea that I could use cheap, Ikea cabinet door fronts that I found in their as is section for $8 each. After cutting one opening I realized that I could make the doors work and I cut the second opening on the left side. I knew there was electrical behind that side so I proceeded with caution. After the holes were cut, I cut 2x4s to frame the opening. I made sure the 2x4s were a really tight fit so that I could mallet them into position and then use long wood screws to secure them to the studs at an angle. On the bottom left I made the frame by connecting three boards that I could secure in around the electrical. After this was complete, I felt that I needed a bit more structural support, so I added 2x4s horizontally across, over the electrical box. You'll see the position in the next step.

Paint, Contact Paper and Doors

20240407_104450.jpg
20240407_104505.jpg
20240407_105921.jpg
20240407_113351.jpg
20240407_113406.jpg

I started by attaching the hinges to the Ikea doors and marking where they would attach to the studs. I needed an extra pair of hands for this. My husband helped hold the doors while I marked, I found that easier than trying to measure between the hinges spaces. I made sure the doors would open and close and adjusted the hinges accordingly. I didn't want to make it any more shallow by adding a backing board, so I put contact paper directly on the drywall. I had this contact paper left over from a previous project.

Building and Attaching the Frame

20240407_134015.jpg
20240407_184348.jpg
20240407_184353.jpg
20240407_185501.jpg
20240407_185640.jpg

I measured the frame with a 1/4" gap around all sides. I attached the corners with brad nails and put on some painters tape to make sure it held it's shape. I slid the frame over some spacers that were taped to the doors. I used the brad nailer to secure the frame around the doors.

The Inspiration

20240409_101656.jpg
20240416_182359.jpg

This part was kind of crazy. I sat and looked at these doors day after day trying to figure out what they should look like. I had found the wall paper for the wall, but could not grasp a concept for the doors themselves. I tried different patterns in painters tape, I drew on the doors, and I sat back and stared at them knowing that none of this was right. I kept scouring the internet for ideas and could not get motivated. With the frame this opening is 52' x 44", a pretty substantial size, I wanted it to look good.

Shelves and Magnets

20241112_103734.jpg
20241112_103806.jpg

While I waited for creative inspiration, I added some simple shelves and door magnets. I screwed small wood blocks into the studs and attached the shelves with brad nails through the top.

The Artwork!

IMG_20241111_191954.jpg
IMG_20241111_192022.jpg
IMG_20241111_192024.jpg
IMG_20241111_192025.jpg

I was so stuck on the artwork for the cabinets and I decided to walk through Ikea for inspiration. I was in the art section and saw this rolled canvas hanging on display. I knew immediately that was it! I took it home and started figuring out how to attach it. I checked the internet for some tips, but couldn't find anyone who had attached a canvas to kitchen cabinets. So I decided that I was going with Mod Podge. I started by stretching the canvas over the opening and pinning it in place. I lowered the top half and added glue to the doors and then smoothed it back up and pinned it again. This was not easy and quite messy, but it worked! I repeated this on the bottom half, I unpinned lifted up and added glue to the doors. Even more messy than the top. The glue took longer to dry behind the canvas than I expected. It was a few days before I took the next step. I took my sharpest blade and cut carefully around the doors. I made sure I was inside the gaps all the way around. I removed the doors, laid them out and added a top coat of the Mod Podge. I went back to glue the frame with the same technique as the doors. I would take out the pins and pull back one side, add glue, smooth out and put the pins back in. I focused on the front and left the sides without glue because I thought they would be easier to glue down after cutting off the excess. So after the fronts were dry I trimmed them and glued down the sides. When they were dry I did a top coat of Mod Podge. I trimmed the doors with a sharp blade and got a really clean edge.

The Details

20241111_192441.jpg
20241111_192444.jpg
20241111_195423.jpg
20241112_095703.jpg

After I put up my wallpaper, I found myself bothered by the white gaps I could see around the painting. I took the paint that I had used for the shelves and added some acrylic paint to make a pallet that blended with the canvas. I went around all the corners and dabbed on paint to make the transitions less noticeable. I'm really happy with how this turned out. I did it around the doors and around the inside of the frame. Now from all angles it looks like a solid piece instead of seeing all the white. The white really killed the illusion. I found thin black handles that blend into the dark rocks in the picture. I love this detail, they really seem hidden.

Covering the Outlet Box

20241111_194524.jpg
20241111_194826.jpg
20241111_194830.jpg
20241111_195049.jpg
20241111_195259.jpg
20241111_195313.jpg

The only thing I had left was to cover the opening around the outlet box. I wanted something simple and easy to remove. So I grabbed a thick carboard sheet (a cover of a construction paper set) and some removable vinyl. I cut the cardboard to cover the hole and set it on some white vinyl. I tucked it into place and trimmed the edges with a sharp blade. A very simple solution and the project was complete!

I absolutely love how this turned out!

I hope that this Instructable inspires you to try something that you've never seen done before and trust your own creativity.